update esp toolchain to [rust] 1.69

closes #4
closes #12

.gitignore

@@ -2,3 +2,4 @@
 /.embuild
 /target
 /Cargo.lock
+/secret

Cargo.toml

@@ -19,7 +19,9 @@ esp-idf-hal = "0.37.4"
 esp-idf-sys = { version = "0.31.5", features = ["binstart", "native"] }
 mqtt-protocol = "0.11.2"
 nb = "1.0.0"
-ublox = "0.4.2"
+nmea0183 = "0.3.0"
+serde-json-core = "0.5.0"
+serde = "*"
 
 [build-dependencies]
 embuild = "0.29"

rust-toolchain.toml

@@ -1,2 +1,2 @@
 [toolchain]
-channel = "esp"
+channel = "esp-1.69.0.0"

sdkconfig.defaults

@@ -1,5 +1,5 @@
 # Rust often needs a bit of an extra main task stack size compared to C (the default is 3K)
-CONFIG_ESP_MAIN_TASK_STACK_SIZE=64000
+CONFIG_ESP_MAIN_TASK_STACK_SIZE=128000
 
 # Use this to set FreeRTOS kernel tick frequency to 1000 Hz (100 Hz by default).
 # This allows to use 1 ms granuality for thread sleeps (10 ms by default).

src/command.rs

@@ -12,7 +12,7 @@ impl Command {
         Command {
             text: "ATI".to_string(),
             timeout: Duration::from_millis(6000),
-            contains: Some("+CIEV".to_string()),
+            contains: Some("OK".to_string()),
         }
     }
 
@@ -236,7 +236,7 @@ impl Command {
         Command {
             text: "AT".to_string(),
             timeout: Duration::from_millis(3000),
-            contains: Some("+CIEV".to_string()),
+            contains: Some("OK".to_string()),
         }
     }
 

src/config.rs

@@ -1,11 +1,19 @@
+#![allow(dead_code)]
+
 pub struct GprsAp<'a> {
     pub apn: &'a str,
     pub username: &'a str,
     pub password: &'a str,
 }
 
-pub const A1_GPRS_AP: GprsAp = GprsAp {
+pub const A1: GprsAp = GprsAp {
     apn: "internet",
     username: "internet",
     password: "internet",
 };
+
+pub const MTS: GprsAp = GprsAp {
+    apn: "gprswap",
+    username: "mts",
+    password: "064",
+};

src/gps.rs

@@ -3,96 +3,41 @@ use anyhow;
 use std::{
     sync::mpsc::SyncSender,
     thread,
-    time::{Duration, Instant},
+    time::Duration,
-    io::{Read, Write},
+    io::Read,
 };
 
 use esp_idf_hal::prelude::*;
 use esp_idf_hal::serial::{self, Rx, Tx};
 
-use ublox::*;
+use nmea0183::{Parser, ParseResult, Sentence, Source};
 
-use crate::types::*;
+use crate::types::Msg;
 use crate::serial::SerialIO;
 
 struct GpsModule<UART: serial::Uart> {
     port: SerialIO<UART>,
-    parser: Parser<Vec<u8>>,
 }
 
 impl<UART: serial::Uart> GpsModule<UART> {
     pub fn new(tx: Tx<UART>, rx: Rx<UART>) -> Self {
-        let parser = Parser::default();
+        GpsModule {
-        GpsModule { port: SerialIO::new(tx, rx), parser }
+            port: SerialIO::new(tx, rx),
-    }
-
-    pub fn write_all(&mut self, data: &[u8]) -> std::io::Result<()> {
-        println!("WRITE: {:?}", data);
-        self.port.write(data).map(|_| ())
-    }
-
-    pub fn update<T: FnMut(PacketRef)>(&mut self, mut cb: T) -> std::io::Result<()> {
-        println!("UPDATING ...     ...     ...");
-        loop {
-            let mut local_buf = [0; 1024];
-            let nbytes = self.read_port(&mut local_buf)?;
-            if nbytes == 0 {
-                println!("no bytes to read :(");
-                break;
-            }
-            // parser.consume adds the buffer to its internal buffer, and
-            // returns an iterator-like object we can use to process the packets
-            let mut it = self.parser.consume(&local_buf[..nbytes]);
-            while let Some(Ok(packet)) = it.next() {
-                println!("READ: {:?}", packet);
-                cb(packet);
-            }
-        }
-        Ok(())
-    }
-
-    pub fn wait_for_ack<T: UbxPacketMeta>(&mut self, timeout: Duration) -> std::io::Result<bool> {
-        let mut found_packet = false;
-        println!("LOOKING FOR ACK ...");
-        let start = Instant::now();
-        while !found_packet && start.elapsed() < timeout {
-            self.update(|packet| {
-                if let PacketRef::AckAck(ack) = packet {
-                    if ack.class() == T::CLASS && ack.msg_id() == T::ID {
-                        println!("FOUND PACKET: {} {}", ack.class(), ack.msg_id());
-                        found_packet = true;
-                    }
-                }
-                else if let PacketRef::AckNak(nak) = packet {
-                    println!("NAK PACKET: {} {}", nak.class(), nak.msg_id());
-                }
-            })?;
-        }
-        println!("exiting wait_for_ack");
-        Ok(found_packet)
-    }
-
-    /// Reads the serial port, converting timeouts into "no data received"
-    fn read_port(&mut self, output: &mut [u8]) -> std::io::Result<usize> {
-        match self.port.read(output) {
-            Ok(b) => Ok(b),
-            Err(e) => {
-                if e.kind() == std::io::ErrorKind::TimedOut {
-                    Ok(0)
-                } else {
-                    Err(e)
-                }
-            }
         }
     }
 }
 
-pub fn main<T: Sync + Send>(
+pub fn main<PRx,PTx>
-    tx: esp_idf_hal::gpio::Gpio12<T>,
+(
-    rx: esp_idf_hal::gpio::Gpio13<T>,
+    tx: PTx,
+    rx: PRx,
     uart: serial::UART2,
     sender: SyncSender<Msg>,
-) -> Result<(), anyhow::Error> {
+) -> std::result::Result<(), anyhow::Error>
+where
+    PRx: esp_idf_hal::gpio::Pin + esp_idf_hal::gpio::InputPin + esp_idf_hal::gpio::OutputPin,
+    PTx: esp_idf_hal::gpio::Pin + esp_idf_hal::gpio::InputPin + esp_idf_hal::gpio::OutputPin,
+{
     let serial_pins = serial::Pins {
         tx,
         rx,
@@ -100,100 +45,46 @@ pub fn main<T: Sync + Send>(
         rts: None,
     };
 
-    let serial_config = serial::config::Config::default()
-        .baudrate(Hertz(9600))
-        .data_bits(serial::config::DataBits::DataBits8)
-        .parity_none()
-        .flow_control(serial::config::FlowControl::None)
-        .stop_bits(serial::config::StopBits::STOP1);
-
     let serial: serial::Serial<serial::UART2, _, _> = serial::Serial::new(
         uart,
         serial_pins,
-        serial_config,
+        serial::config::Config::default().baudrate(Hertz(9600)),
     )?;
 
     let (tx, rx) = serial.split();
     let mut device = GpsModule::new(tx, rx);
 
-    // Configure the device to talk UBX
+    let mut parser = Parser::new()
-    device
+        .source_only(Source::GPS)
-        .write_all(
+        .sentence_filter(Sentence::GLL | Sentence::GGA);
-            &CfgPrtUartBuilder {
-                portid: UartPortId::Uart1,
-                reserved0: 0,
-                tx_ready: 0,
-                mode: UartMode::new(DataBits::Eight, Parity::None, StopBits::One),
-                baud_rate: 9600,
-                in_proto_mask: InProtoMask::all(),
-                out_proto_mask: OutProtoMask::UBOX,
-                flags: 0,
-                reserved5: 0,
-            }
-            .into_packet_bytes(),
-        )?;
-    device.wait_for_ack::<CfgPrtUart>(Duration::from_millis(3000)).unwrap();
-    println!("CfgPrtUart acked!");
 
-    // Set interval for the NavPosVelTime packet
+    let mut c = 0;
-    println!("Sending set_rate_for::<NavPosVelTime> ...");
+    let mut nmea = [0_u8; 1024];
-    for i in 1..5 {
+    loop {
-        device
+        if let Ok(_) = device.port.read(nmea.as_mut_slice()) {
-            .write_all(
+            println!("\r\n\r\n\r\n\r\n");
-                &CfgMsgAllPortsBuilder::set_rate_for::<NavPosVelTime>([0, 1, 1, 0, 0, 0])
+            for result in parser.parse_from_bytes(&nmea[..]) {
-                .into_packet_bytes(),
+                match result {
-            )
+                    Ok(ParseResult::GLL(Some(gll))) => {
-            .unwrap();
+                        sender.send(Msg::Gps(gll.into()))?;
-        println!("SENT set_rate_for::<NavPosVelTime>({}) !!!", i);
+                    },
-        if let Ok(true) = device.wait_for_ack::<CfgMsgSinglePort>(Duration::from_millis(3000)) {
+                    Ok(ParseResult::GGA(Some(gga))) => {
-            println!("Setting rate for NavPosVelTime acked! Exiting loop ...");
+                        sender.send(Msg::Gps(gga.into()))?;
-            break
-        }
-    }
-
-    // Send a packet request for the MonVer packet
-    //device
-    //    .write_all(&UbxPacketRequest::request_for::<MonVer>().into_packet_bytes())
-    //    .unwrap();
-
-    // Start reading data
-    println!("Opened u-blox device, waiting for solutions...");
-    for _ in 0..20 {
-        device
-            .update(|packet| match packet {
-                PacketRef::MonVer(packet) => {
-                    println!(
-                        "SW version: {} HW version: {}",
-                        packet.software_version(),
-                        packet.hardware_version()
-                    );
-                    println!("{:?}", packet);
-                }
-                PacketRef::NavPosVelTime(sol) => {
-                    let has_posvel = sol.fix_type() == GpsFix::Fix3D
-                        || sol.fix_type() == GpsFix::GPSPlusDeadReckoning;
-
-                    if has_posvel {
-                        let pos: Position = (&sol).into();
-                        let vel: Velocity = (&sol).into();
-                        let solution = Solution {
-                            latitude: pos.lat,
-                            longitude: pos.lon,
-                            altitude: pos.alt,
-                            speed: vel.speed,
-                            direction: vel.heading,
-                        };
-                        println!("Sol: {:?}", solution);
-                        sender.send(Msg::Gps(solution));
                     }
+                    _ => { }
                 }
-                _ => {
+            }
-                    println!("{:?}", packet);
+            c = 0;
-                }
+        } else {
-            })?;
+            println!("nothing to read after {} tries ...", c);
-        thread::sleep(Duration::from_millis(1000));
+            if c > 100 {
+                println!("reached {} retries ... bailing!", c);
+                break;
+            }
+        }
+        thread::sleep(Duration::from_millis(5000));
+        c += 1;
     }
 
-    println!("exiting GPS sender loop :)");
     Ok(())
 }

src/main.rs

@@ -5,10 +5,15 @@ mod command;
 mod modem;
 mod serial;
 mod types;
+mod gps;
 
 use anyhow;
 use std::{thread::{self, JoinHandle}, time::Duration};
 use esp_idf_hal::peripherals::Peripherals;
+use esp_idf_hal::prelude::*;
+use esp_idf_hal::serial::{Pins, config::Config, Serial, UART1, Uart};
+use embedded_hal::digital::v2::OutputPin;
+
 use types::*;
 
 fn main() -> anyhow::Result<()> {
@@ -18,6 +23,25 @@ fn main() -> anyhow::Result<()> {
 
     println!("Rust main thread: {:?}", thread::current());
 
+    let mut threads: Vec<JoinHandle<anyhow::Result<_>>> = vec![];
+
+    // // Rx/Tx pins for the GPS modem
+    let gps_rx = dp.pins.gpio32;
+    let gps_tx = dp.pins.gpio33;
+    // // UART interface for the GPS modem
+    let gps_uart = dp.uart2;
+
+
+    let (gps_sender, receiver) = std::sync::mpsc::sync_channel::<Msg>(3);
+    //let accel_sender = gps_sender.clone();
+
+    //let _ = gps::main(gps_tx, gps_rx, gps_uart, gps_sender)?;
+    //threads.push(thread::spawn(move || accel::main(accel_sender)));
+
+    // ==================================
+    // MODEM INITIALIZATION AND MAIN LOOP
+    // ==================================
+
     // LilyGo TTGO T-Call sim800l board serial pins.
     let modem_rx = dp.pins.gpio26;
     let modem_tx = dp.pins.gpio27;
@@ -28,24 +52,38 @@ fn main() -> anyhow::Result<()> {
     // UART interface for the GSM modem
     let modem_uart = dp.uart1;
 
-    let mut threads: Vec<JoinHandle<anyhow::Result<_>>> = vec![];
+    let serial_pins = Pins {
+        tx: modem_tx,
+        rx: modem_rx,
+        cts: None,
+        rts: None,
+    };
 
-    // // Rx/Tx pins for the GPS modem
+    let serial: Serial<UART1, _, _> = Serial::new(
-    // let gps_rx = dp.pins.gpio13;
+        modem_uart,
-    // let gps_tx = dp.pins.gpio12;
+        serial_pins,
-    // // UART interface for the GPS modem
+        Config::default().baudrate(Hertz(115200)),
-    // let gps_uart = dp.uart2;
+    )?;
 
+    let (tx, rx) = serial.split();
+    type PwrkeyOutput = esp_idf_hal::gpio::Gpio4<esp_idf_hal::gpio::Output>;
+    type ResetOutput = esp_idf_hal::gpio::Gpio5<esp_idf_hal::gpio::Output>;
+    type PowerOutput = esp_idf_hal::gpio::Gpio23<esp_idf_hal::gpio::Output>;
 
-    let (gps_sender, receiver) = std::sync::mpsc::sync_channel::<Msg>(1);
+    let mut mdm: modem::Modem<UART1, PwrkeyOutput, ResetOutput, PowerOutput> = modem::Modem::new(tx, rx, modem_pwrkey, modem_rst, modem_power, receiver);
-    let accel_sender = gps_sender.clone();
 
-    // let _ = gps::main(gps_tx, gps_rx, gps_uart, gps_sender)?;
+    let mqtt_username = include_str!("../secret/username").trim();
-    // threads.push(thread::spawn(move || gps::main(gps_rx, gps_tx, gps_uart, gps_sender)));
+    let mqtt_password = include_str!("../secret/password").trim();
-    thread::sleep(Duration::from_millis(1000));
-    threads.push(thread::spawn(move || accel::main(accel_sender)));
 
-    let _ = modem::main(modem_rx, modem_tx, modem_uart, modem_pwrkey, modem_rst, modem_power, receiver)?;
+    threads.push(thread::spawn(move || gps::main(gps_tx, gps_rx, gps_uart, gps_sender.clone())));
 
-    Ok(())
+    println!("======================= MAIN =======================");
+    mdm.init().unwrap_or(());
+    let _ = mdm.echo(false).unwrap_or(());
+    println!("resetting modem ... ");
+    println!("======================= MODEM =======================");
+    let _ = mdm.mqtt_send_position_loop("51.158.66.64", 7887, mqtt_username, mqtt_password).unwrap_or(());
+    let _ = mdm.tcp_close_connection().unwrap_or(());
+    thread::sleep(Duration::from_millis(1500));
+    panic!("rebooting");
 }

src/modem.rs

@@ -1,3 +1,5 @@
+#![allow(dead_code)]
+
 use crate::command::Command;
 use crate::serial::SerialIO;
 use crate::types::*;
@@ -11,20 +13,25 @@ use std::{
     sync::mpsc::Receiver,
 };
 
-use esp_idf_hal::prelude::*;
 use esp_idf_hal::serial::{self, Rx, Tx};
 
 use embedded_hal::digital::v2::OutputPin;
 
-use mqtt::packet::{ConnectPacket, PublishPacket, QoSWithPacketIdentifier, VariablePacket};
+use mqtt::{
-use mqtt::{Encodable, Decodable, TopicName};
+    Encodable,
+    Decodable,
+    TopicName,
+    packet::{
+        ConnectPacket,
+        PublishPacket,
+        QoSWithPacketIdentifier,
+        VariablePacket,
+    },
+};
+use serde_json_core;
 
 pub type Result<T> = std::result::Result<T, ModemError>;
 
-pub struct Modem<UART: serial::Uart> {
-    serial: SerialIO<UART>,
-}
-
 #[derive(Debug)]
 pub enum ModemError {
     CommandError(String),
@@ -42,10 +49,22 @@ impl std::fmt::Display for ModemError {
     }
 }
 
-impl<UART: serial::Uart> Modem<UART> {
+pub struct Modem<UART: serial::Uart, PWK: OutputPin, RST: OutputPin, PW: OutputPin> {
-    pub fn new(tx: Tx<UART>, rx: Rx<UART>) -> Self {
+    serial: SerialIO<UART>,
+    reset: RST,
+    power: PW,
+    power_key: PWK,
+    receiver: Receiver<Msg>,
+}
+
+impl<UART: serial::Uart, PWK: OutputPin, RST: OutputPin, PW: OutputPin> Modem<UART, PWK, RST, PW> {
+    pub fn new(tx: Tx<UART>, rx: Rx<UART>, mut pwrkey: PWK, mut rst: RST, mut power: PW, receiver: Receiver<Msg>) -> Self {
         Self {
             serial: SerialIO::new(tx, rx),
+            reset: rst,
+            power,
+            power_key: pwrkey,
+            receiver,
         }
     }
 
@@ -64,30 +83,31 @@ impl<UART: serial::Uart> Modem<UART> {
     ///
     /// modem::init(modem_pwrkey, modem_rst, modem_power);
     /// ```
-    pub fn init(&mut self, mut pwrkey: impl OutputPin, mut rst: impl OutputPin, mut power: impl OutputPin) -> Result<()> {
+    pub fn init(&mut self) -> Result<()> {
         println!("Turning SIM800L on ...");
-        power.set_high().map_err(|_| ModemError::SetupError("Error setting POWER to high.".to_string()))?;
+        self.power.set_high().map_err(|_| ModemError::SetupError("Error setting POWER to high.".to_string()))?;
-        //rst.set_high().map_err(|_| ModemError::SetupError("Error setting RST to high.".to_string()))?;
+        self.reset.set_high().map_err(|_| ModemError::SetupError("Error setting RST to high.".to_string()))?;
         // Pull down PWRKEY for more than 1 second according to manual requirements
-        pwrkey.set_high().map_err(|_| ModemError::SetupError("Error setting PWRKEY to high.".to_string()))?;
+        self.power_key.set_high().map_err(|_| ModemError::SetupError("Error setting PWRKEY to high.".to_string()))?;
         thread::sleep(Duration::from_millis(1500));
-        pwrkey.set_low().map_err(|_| ModemError::SetupError("Error setting PWRKEY to low.".to_string()))?;
+        self.power_key.set_low().map_err(|_| ModemError::SetupError("Error setting PWRKEY to low.".to_string()))?;
         thread::sleep(Duration::from_millis(1000));
-        pwrkey.set_high().map_err(|_| ModemError::SetupError("Error setting PWRKEY to high.".to_string()))?;
+        self.power_key.set_high().map_err(|_| ModemError::SetupError("Error setting PWRKEY to high.".to_string()))?;
         println!("Waiting for sim module to come online ...");
         thread::sleep(Duration::from_millis(3000));
-        loop {
+        for _ in 0..10 {
-            match self.send_command(Command::probe()) {
+            let _ = self.send_command(Command::probe()).unwrap_or("".to_string());
-                Ok(_) => break,
+            thread::sleep(Duration::from_millis(1000));
-                _ => {
-                    thread::sleep(Duration::from_millis(2000));
-                    continue
-                },
-            }
         }
+        self.serial.clear();
         Ok(())
     }
 
+    pub fn echo(&mut self, enabled: bool) -> Result<()> {
+        let cmd = format!("ATE{}", if enabled { 1 } else { 0 });
+        self.send(&cmd, "OK").map(|_| ())
+    }
+
     /// Reads the serial RX until the `contains` string is encoutered if `contains` is Some(s), if
     /// None, then the first line is returned. If a timeout is reached. The timeout is provided on
     /// input via the `timeout` argument. The first argument `contains` is checked against every
@@ -114,7 +134,7 @@ impl<UART: serial::Uart> Modem<UART> {
             if response.contains(&c) {
                 Ok(response)
             } else {
-                Err(ModemError::CommandError(format!("Didn't get expected ({}) from modem.", c)))
+                Err(ModemError::CommandError(format!("Didn't get expected ({}) from modem. Got: {}", c, response)))
             }
         } else {
             Ok(response)
@@ -130,6 +150,7 @@ impl<UART: serial::Uart> Modem<UART> {
     }
 
     fn send(&mut self, at_command: &str, contains: &str) -> Result<String> {
+        self.serial.clear();
         println!("-----------------------------------------------------------");
         println!("Sending {} ...", at_command);
 
@@ -171,7 +192,7 @@ impl<UART: serial::Uart> Modem<UART> {
         let _ = self.handle_prompt()?;
         println!("Handled prompt OK!!");
 
-        println!("Writing bytes in serial TX! ({:?})", String::from_utf8(buf.to_vec()));
+        println!("Writing bytes in serial TX! ({:?})", buf.into_iter().map(|b| char::from(*b)).collect::<String>());
         self.serial
             .write_bytes(buf)
             .map_err(|err| ModemError::SendDataError(format!("{:?}", err)))?;
@@ -197,15 +218,15 @@ impl<UART: serial::Uart> Modem<UART> {
         self.send_command(Command::gprs_bearer_status())
     }
 
-    pub fn gprs_attach_ap(&mut self, apn: &str, username: &str, password: &str)-> Result<()> {
+    pub fn gprs_attach_ap(&mut self, config: crate::config::GprsAp)-> Result<()> {
         println!("init gprs ...");
         let _ = self.send_command(Command::gprs_init())?;
 
-        println!("setting up gprs credentials for apn {}, {}:{})", apn, username, password);
+        println!("setting up gprs credentials for apn {}, {}:{})", config.apn, config.username, config.password);
 
-        let _ = self.send_command(Command::gprs_set_apn(apn))?;
+        let _ = self.send_command(Command::gprs_set_apn(config.apn))?;
-        let _ = self.send_command(Command::gprs_set_user(username))?;
+        let _ = self.send_command(Command::gprs_set_user(config.username))?;
-        let _ = self.send_command(Command::gprs_set_pwd(password))?;
+        let _ = self.send_command(Command::gprs_set_pwd(config.password))?;
 
         Ok(())
     }
@@ -223,6 +244,7 @@ impl<UART: serial::Uart> Modem<UART> {
 
     fn try_connect_gprs(&mut self) -> Result<()> {
         let mut retries = 0;
+        println!("TRYING TO CONNECT TO GPRS");
         loop {
             if self.is_gprs_attached()? {
                 let _ = self.gprs_connect()?;
@@ -258,17 +280,29 @@ impl<UART: serial::Uart> Modem<UART> {
 
     pub fn tcp_connect(&mut self, addr: &str, port: u16) -> Result<()> {
         let at_command = format!("AT+CIPSTART=\"TCP\",\"{}\",\"{}\"", addr, port);
-        let _ = self.send(&at_command, "CONNECT OK");
+        let mut reply_result = self.send(&at_command, "CONNECT OK");
         for _ in 0..3 {
-            if let Ok(reply) = self.command_read_response(Some("CONNECT OK".to_string())) {
+            if let Ok(reply) = reply_result {
                 println!("TCP connect replied with {}", reply);
                 break
+            } else {
+                reply_result = self.command_read_response(Some("CONNECT OK".to_string()));
             }
-            thread::sleep(Duration::from_millis(500));
+            thread::sleep(Duration::from_millis(1000));
         }
         Ok(())
     }
 
+    pub fn tls_connect(&mut self, addr: &str, port: u16) -> Result<()> {
+        let _ = self.tcp_connect(addr, port)?;
+
+        // ------------------------
+        // TLS handshake goes here.
+        // ------------------------
+
+        Ok(())
+    }
+
     pub fn tcp_set_quick_mode(&mut self, mode: bool) -> Result<()> {
         self.send_command(Command::tcp_set_quick_mode(mode))
             .map(|_| ())
@@ -280,6 +314,8 @@ impl<UART: serial::Uart> Modem<UART> {
     }
 
     pub fn tcp_manual_send(&mut self, buf: &[u8]) -> Result<()> {
+        thread::sleep(Duration::from_millis(200));
+        // self.serial.clear();
         self.tcp_manual_send_data(buf)
             .map(|_| ())
     }
@@ -335,8 +371,8 @@ impl<UART: serial::Uart> Modem<UART> {
         }
     }
 
-    pub fn tcp_close_connection(&mut self) -> Result<String> {
+    pub fn tcp_close_connection(&mut self) -> Result<()> {
-        self.send_command(Command::tcp_close())
+        self.send_command(Command::tcp_close()).map(|_| ())
     }
 
     pub fn http_post(&mut self, url: &str, token: &str, content: &[u8]) -> Result<String> {
@@ -450,13 +486,15 @@ impl<UART: serial::Uart> Modem<UART> {
         Err(ModemError::ReadError("TCP server didn't respond!".into()))
     }
 
-    fn mqtt_connect(&mut self, device_id: &str) -> anyhow::Result<()> {
+    fn mqtt_connect(&mut self, device_id: &str, username: &str, password: &str) -> anyhow::Result<()> {
         let mut buf = Vec::new();
         let mut conn = ConnectPacket::new(device_id);
         conn.set_clean_session(true);
         conn.set_keep_alive(100);
+        conn.set_user_name(Some(username.to_string()));
+        conn.set_password(Some(password.to_string()));
         let _ = conn.encode(&mut buf)?;
-        self.tcp_manual_send(&mut buf).ok();
+        let _ = self.tcp_manual_send(&mut buf)?;
 
         let reply = self.mqtt_receive_reply()?;
         println!("mqtt decoded packet: ({:?})", reply);
@@ -476,114 +514,66 @@ impl<UART: serial::Uart> Modem<UART> {
             message.as_bytes(),
         );
         let _ = packet.encode(&mut buf)?;
-        println!("created mqtt publish packet ... ({})",
+        self.tcp_manual_send(&mut buf)?;
-            std::str::from_utf8(buf.as_slice()).unwrap_or(""));
+        Ok(())
-        self.tcp_manual_send(&mut buf).ok();
+    }
+
+    pub fn mqtt_send_position_loop(&mut self, host: &str, port: u16, username: &str, password: &str) -> anyhow::Result<()> {
+        if !self.is_gprs_attached()? {
+            let _ = self.gprs_attach_ap(crate::config::MTS)?;
+            let _ = self.try_connect_gprs()?;
+        }
+        // When command AT+CIPQSEND=0, it is in normal sending mode. In this mode, after user
+        // sends data by AT+CIPSEND, if the server receives TCP data, it will give ACK message
+        // to module, and the module will respond SEND OK.
+        let _ = self.send("AT+CIPQSEND=0", "OK");
+        // Enables getting data from network manually.
+        let _ = self.send("AT+CIPRXGET=1", "OK");
+
+        for _ in 0..5 {
+            if let Ok(_) = self.tcp_connect(host, port) {
+                break
+            }
+        }
+
+        let device_id = "c36a72df-5bd6-4f9b-995d-059433bc3267";
+        println!("connecting to MQTT with ({}:{})", username, password);
+        let _ = self.mqtt_connect(device_id, username, password)?;
+
+        println!("entering queue receive loop ...");
+        let mut err_count = 0;
+        let _ = loop {
+            match self.receiver.recv() {
+                Ok(Msg::Gps(solution)) => {
+                    println!("received GPS solution {:?} | sending to mqtt ...", solution);
+                    serde_json_core::ser::to_string::<Solution, 512>(&solution)
+                        .map_err(|e| anyhow::Error::new(e))
+                        .and_then(|sol| self.mqtt_publish(device_id, &sol))?;
+                    err_count = 0;
+                },
+                Ok(Msg::Accelerometer(acc)) => {
+                    println!("received accel {} | sending to mqtt ...", acc);
+                    let _ = self.mqtt_publish(device_id, &format!("{:?}", acc))?;
+                    err_count = 0;
+                }
+                Err(e) => {
+                    if err_count < 5 {
+                        err_count += 1;
+                        println!("received error {} | NOT sending to mqtt ...", e);
+                    }
+                    else {
+                        break
+                    }
+                }
+            }
+        };
+
         Ok(())
     }
 }
 
-impl<UART: serial::Uart> std::io::Read for Modem<UART> {
+impl<UART: serial::Uart, PWK: OutputPin, RST: OutputPin, PW: OutputPin> std::io::Read for Modem<UART, PWK, RST, PW> {
     fn read(&mut self, buf: &mut [u8]) -> std::io::Result<usize> {
         self.tcp_receive(buf).map_err(|_| std::io::Error::from(std::io::ErrorKind::ConnectionAborted))
     }
 }
-
-pub fn main<T: Sync + Send>(
-    rx: esp_idf_hal::gpio::Gpio26<T>,
-    tx: esp_idf_hal::gpio::Gpio27<T>,
-    uart: serial::UART1,
-    pwrkey: esp_idf_hal::gpio::Gpio4<esp_idf_hal::gpio::Output>,
-    rst: esp_idf_hal::gpio::Gpio5<esp_idf_hal::gpio::Output>,
-    power: esp_idf_hal::gpio::Gpio23<esp_idf_hal::gpio::Output>,
-    receiver: Receiver<Msg>,
-) -> std::result::Result<(), anyhow::Error> {
-    let serial_pins = serial::Pins {
-        tx,
-        rx,
-        cts: None,
-        rts: None,
-    };
-
-    let serial: serial::Serial<serial::UART1, _, _> = serial::Serial::new(
-        uart,
-        serial_pins,
-        serial::config::Config::default().baudrate(Hertz(115200)),
-    )?;
-
-    let (tx, rx) = serial.split();
-    let mut mdm = Modem::new(tx, rx);
-
-    mdm.init(pwrkey, rst, power)?;
-
-    // thread::sleep(Duration::from_millis(500));
-
-    //println!("setting up client TLS cert");
-    //let client_cert = include_bytes!("../certs/full-bin.p12");
-    //let client_cert_path = "C:\\USER\\fullchain.pem";
-
-    //let _ = mdm.upload_cert(client_cert_path, client_cert)?;
-    //let _ = mdm.ssl_set_client_cert(client_cert_path, "t")?;
-    //let _ = mdm.fs_list("C:\\USER\\")?;
-
-    // Retry 5 times to open a TCP connection, otherwise fail and wait for reboot.
-    let mut retries = 0;
-
-    loop {
-        if !mdm.is_gprs_attached()? {
-            let _ = mdm.gprs_attach_ap(
-                crate::config::A1_GPRS_AP.apn,
-                crate::config::A1_GPRS_AP.username,
-                crate::config::A1_GPRS_AP.password,
-            )?;
-        }
-        if let Ok(()) = mdm.try_connect_gprs() {
-            let device_id = "c36a72df-5bd6-4f9b-995d-059433bc3267";
-
-            // When command AT+CIPQSEND=0, it is in normal sending mode. In this mode, after user
-            // sends data by AT+CIPSEND, if the server receives TCP data, it will give ACK message
-            // to module, and the module will respond SEND OK.
-            let _ = mdm.send("AT+CIPQSEND=0", "OK");
-            // Enables getting data from network manually.
-            let _ = mdm.send("AT+CIPRXGET=1", "OK");
-
-            if let Err(_) = mdm.tcp_connect("51.158.66.64", 7887) {
-                if retries < 5 {
-                    retries += 1;
-                    continue;
-                }
-            }
-            thread::sleep(Duration::from_millis(500));
-            mdm.serial.clear();
-
-            let _ = mdm.mqtt_connect(device_id)?;
-
-            println!("entering queue receive loop ...");
-            let mut err_count = 0;
-            let _ = loop {
-                match receiver.recv() {
-                    Ok(Msg::Gps(solution)) => {
-                        println!("received GPS solution {:?} | sending to mqtt ...", solution);
-                        let _ = mdm.mqtt_publish(device_id, &format!("{:?}", solution))?;
-                        err_count = 0;
-                    },
-                    Ok(Msg::Accelerometer(acc)) => {
-                        println!("received accel {} | sending to mqtt ...", acc);
-                        let _ = mdm.mqtt_publish(device_id, &format!("{:?}", acc))?;
-                        err_count = 0;
-                    }
-                    Err(e) => {
-                        if err_count < 5 {
-                            err_count += 1;
-                            println!("received error {} | NOT sending to mqtt ...", e);
-                        }
-                        else {
-                            break
-                        }
-                    }
-                }
-            };
-            let _ = mdm.tcp_close_connection()?;
-        }
-    }
-}

src/types.rs

@@ -1,14 +1,106 @@
-#[derive(Debug)]
+#![allow(dead_code)]
+use nmea0183::{
+    GGA,
+    GLL,
+    coords::{
+        Latitude as NMEALatitude,
+        Longitude as NMEALongitude,
+        Hemisphere as NMEAHemisphere,
+    },
+};
+use serde::Serialize;
+
+#[derive(Debug, Serialize)]
+pub enum Hemisphere {
+    North,
+    South,
+    East,
+    West,
+}
+
+#[derive(Debug, Serialize)]
+pub struct Latitude {
+    degrees: u8,
+    minutes: u8,
+    seconds: f32,
+    hemisphere: Hemisphere,
+}
+
+#[derive(Debug, Serialize)]
+pub struct Longitude {
+    degrees: u8,
+    minutes: u8,
+    seconds: f32,
+    hemisphere: Hemisphere,
+}
+
+impl From<NMEALatitude> for Latitude {
+    fn from(lat: NMEALatitude) -> Self {
+        Self {
+            degrees: lat.degrees,
+            minutes: lat.minutes,
+            seconds: lat.seconds,
+            hemisphere: lat.hemisphere.into(),
+        }
+    }
+}
+
+impl From<NMEALongitude> for Longitude {
+    fn from(lon: NMEALongitude) -> Self {
+        Self {
+            degrees: lon.degrees,
+            minutes: lon.minutes,
+            seconds: lon.seconds,
+            hemisphere: lon.hemisphere.into(),
+        }
+    }
+}
+
+impl From<NMEAHemisphere> for Hemisphere {
+    fn from(hem: NMEAHemisphere) -> Self {
+        match hem {
+            NMEAHemisphere::North => Self::North,
+            NMEAHemisphere::South => Self::South,
+            NMEAHemisphere::East => Self::East,
+            NMEAHemisphere::West => Self::West,
+        }
+    }
+}
+
+#[derive(Debug, Serialize)]
 pub struct Solution {
-    pub latitude: f64,
+    pub latitude: Latitude,
-    pub longitude: f64,
+    pub longitude: Longitude,
-    pub altitude: f64,
+    pub altitude: Option<f32>,
-    pub speed: f64,
+    pub speed: Option<f32>,
-    pub direction: f64,
+    pub direction: Option<f32>,
+}
+
+impl From<GGA> for Solution {
+    fn from(gga: GGA) -> Self {
+        Self {
+            latitude: gga.latitude.into(),
+            longitude: gga.longitude.into(),
+            altitude: Some(gga.altitude.meters),
+            speed: None,
+            direction: None,
+        }
+    }
+}
+
+impl From<GLL> for Solution {
+    fn from(gll: GLL) -> Self {
+        Self {
+            latitude: gll.latitude.into(),
+            longitude: gll.longitude.into(),
+            altitude: None,
+            speed: None,
+            direction: None,
+        }
+    }
 }
 
 pub enum Msg {
     Gps(Solution),
     Accelerometer(String),
 }
-